How to diagnose network connectivity problems from the command line

It happens to all of us. You try to visit a website, and all you get is a blank page, with a slowly spinning wheel of death in the browser tab. Why can’t you connect? The cause of your problem could lie at any of several locations between you and the website. Here, I will tell you how to find exactly where it is. (The following commands are available in both Unix/Linux and Windows/DOS, so they will probably be applicable with whatever operating system you are using.)

Let’s say you’re trying to get to and you encounter connectivity problems. First, you need to test your network interface card (NIC) to see if it’s working. You do this by testing the loopback interface, which is represented by the IP address

# ping
PING ( 56 data bytes
64 bytes from icmp_seq=0 ttl=64 time=0.065 ms
64 bytes from icmp_seq=1 ttl=64 time=0.054 ms
64 bytes from icmp_seq=2 ttl=64 time=0.056 ms
64 bytes from icmp_seq=3 ttl=64 time=0.051 ms

--- ping statistics ---
4 packets transmitted, 4 packets received, 0.0% packet loss
round-trip min/avg/max/stddev = 0.051/0.056/0.065/0.005 ms

Looks like the interface is working. If you ping an address and you get a message than says network timeout or something similar, you know you’ve encountered a dead link. Remember that there are several links, several components, that must work, and if just one of them fails, the entire connection fails.

The next step is to ping the local gateway. To do this, we can take advantage of the fact that on most home and SOHO networks, the local gateway is also the default DNS server. We find the IP address of the local DNS server with the nslookup command.

nslookup is an interactive program for interacting with DNS servers. It is a simple program with only a handful of commands. The only commands we will need here are host and exit.

# nslookup
> host

> exit

Now we ping the local DNS server to see if we can connect to it. If we can’t, one of two things is happening: either the default gateway isn’t working properly, or the connection between our computer and the default gateway is not working.

# ping
PING ( 56 data bytes
64 bytes from icmp_seq=0 ttl=58 time=25.159 ms
64 bytes from icmp_seq=1 ttl=58 time=29.576 ms
64 bytes from icmp_seq=2 ttl=58 time=20.783 ms
64 bytes from icmp_seq=3 ttl=58 time=20.518 ms
--- ping statistics ---
4 packets transmitted, 4 packets received, 0.0% packet loss
round-trip min/avg/max/stddev = 20.518/24.009/29.576/3.705 ms

So that’s working. Now what we have to do is see if the default gateway can connect to the Internet. We do this by pinging one or more websites that are not the website we tried to visit, like say,,,, etc. If these are working, we proceed to the next step.

The next step is to ping the host we are trying to reach. If this is not working, we know that there’s a problem with that server.

# ping

Let’s say that works. Now we proceed to the final step. If all of these links work, then we know it’s probably a problem with the particular port we are trying to access. Let’s say we are trying to go through HTTP. The port number for HTTP is 80. To test a port we need a different tool – the Telnet protocol. Telnet can be used to access any port on a remote host. In this case we are using it to test that port. The command is as follows:

# telnet 80 nodename nor servname provided, or not known

Okay, maybe it wouldn’t look exactly like that, but I couldn’t completely replicate the problem to get the proper error message.

Anyway, now we have found our problem. Port 80 isn’t working. We can either wait for it to start working again, or write to the owners of the server to inform them of the problem.